MANUAL
CCD COLOR CAMERA
IK-629A
(IK-629A)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFEGUARDS
The CAUTION label, shown on the left,
is attached on the bottom of camera.
1. Read Instructions
All the safety and operating instructions should be
12. Lightning
CAUTION TO EDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
For added protection for this video product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the power supply and
cable system. This will prevent damage to the
video product due to lightning and power-line
read before the product is operated.
2. Retain Instructions
The safety instructions and instruction manual
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the instruction
surges.
13. Overloading
Do not overload power supply and extension cords
The lightening flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
manual should be adhered to.
4. Follow Instructions
All operating and use instructions should be
WARNING :
as this can result in a risk of fire or electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this video
followed.
5. Cleaning
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Disconnect this video product from the power
product through openings as they may touch
dangerous voltage points or short-out parts that
could result in a fire or electrical shock. Never spill
supply before cleaning.
6. Attachments
Do not use attachments not recommended by the
CAUTION
CONNECT 24V AC UL LISTED CLASS 2
POWER SUPPLY.
video product manufacturer as they may cause
liquid of kind on the video product.
15. Servicing
Do not attempt to service this video product
hazards.
7. Water and Moisture
Do not use this video product near water-for
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
yourself as opening or removing covers may
expose you to dangerous voltage or other hazards.
example, near a bath tub, wash bowl, kitchen sink,
FIELD INSTALLATION MARKING :
WORDED : "THIS INSTALLATION SHOULD
BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO
ALL LOCAL CODES."
or laundry tub, in
a
wet basement, or near
a
Refer all servicing to qualified service personnel.
16. Damage Requiring service
Disconnect this video product from the power
swimming pool and the like.
8. Accessories
Do not place this video product on an unstable cart,
stand, tripod, bracket or table. The video product
may fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with
stand, tripod, bracket, or table recommended by
the manufacturer, or sold with the video product.
Any mounting of the product should follow the
supply and refer servicing to qualified service
personnel under the following conditions.
a. when the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the video product.
c. If the video product has been exposed to rain or
water.
d. If the video product does not operate normally
manufacturer's instructions, and should use
a
by following the operating instructions in the
instruction manual. Adjust only those controls that
are covered by the instruction manual as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the video product to
mounting accessory recommended by the
INFORMATION
manufacturer.
9. Ventilation
This video product should never be placed near or
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses , and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipmetn in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
over a radiator or heat register. This video product
should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have
its normal operation.
e. If the video product has been dropped or the
cabinet has been damaged.
f. When the video product exhibits
been adhered to.
10. Power Sources
This video product should be operated only from
a
distinct
change in performance-this indicates a need for
service.
17. Replacement Parts
When replacement parts are required, be sure the
the type of power source indicated on the marking
label. If you are not sure of the type of power
USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment
could be voided if you make changes or modifications not expressly approved by the party
supply to your location, consult your product dealer.
11. Power-Cord Protection
Power-Supply cords should be routed so that they
service technician has used replacement parts
specified by the manufacturer with the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, screws and the point
where they exit from the product.
other hazards.
18. Safety Check
Upon completion of any service or repairs to this
video product, ask the service technician to
perform safety checks to determine that the video
product is in proper operating condition.
1. FEATURES & DESCRIPTION :
3. PART NAMES & FUNCTIONS :
1. IK-629A has following functions.
(1) Since this cameras uses AC 24V ~ / DC 12V ---, it can be installed
and built into system easily.
(2) This camera turns color by day to black and white by night
automatically. (DAY/NIGHT function)
(3) Camera synchronization mode is selectable between internal and line-
lock.
(4) This camera adjusts shutter speed according to the subject brightness
automatically. (AES)
(5) BLC is effective when a strong light enters and auto-iris lens closes.
(6) The white balance is automatically adjusted corresponding to the color
temperature variations (AWB)
(7) Easy back focus adjustment makes for easy installations.
2. Built - in 1/3 inch high - sensitivity CCD
3. Minimum illumination of 0.2 lux at F1.2.
4. S/N ratio of 50dB.
5. Horizontal resolution of 350 TV lines.
2. COMPONENTS :
(1) Camera
1
(2) Accessories
(a) Lens Connector
(b) Instruction Manual
(c) Lens Cap
5 0
(E4-191J-100(M))
1
1
1
Line - Lock control
4. CONNECTIONS AND OPERATIONS
Matching the vertical synchronization with the power frequency is called
the Line-Lock.
Notes on connecting
Power plugs of connected equipment must be disconnected before installations.
A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection.
For details of wiring and operation of equipment to be connected, refer to their
operation manuals.
This function is activated when the LINE LOCK switch is set to ON.
O
N
ON
1
2
3
4
OFF
LINE LOCK
Lenses, coaxial cables for video signals and the power cord are not supplied
with the camera.
When two or more cameras are switched by the video switcher for viewing
by a monitor TV, the vertical sync. phase can be locked with the power
frequency, and a stable vertical sync. is obtained without being disturbed
at the time of switching.
1. Basic connection Single system configuration
MONITOR TV
MONITOR TV
CAMERA1
Recorder Ready
VIDEO SWITCHER
CAMERA2
TO 24V AC UL Listed
Class 2 power supply
Recorder Ready
CAMERA
LEVEL
VIDEO OUT
DC 12V ...
H
L
Cautions :
AES VIDEO DC
The camera is synchronized to the power frequency of 60 1 Hz covering
a normal fluctuation of the power frequency. However, the camera may not
cover a large fluctuation caused from the power generated by an engine
generator, etc.
V
PHASE
AC 24V
~
GND
AC 120V
It takes about 10 seconds or more until a stable synchronization is obtained
after the power is turned on. This is normal, because several seconds are
required to stabilize the camera against power noise.
(
) POWER CORD (twisted pair line)
minimum wire size of 18 AWG is recommended.
24V AC UL Listed Class 2 power supply / 12V DC power supply
Refer to "9. LINE-LOCK PHASE" for adjustment.
CAUTION : Never input 24V AC and 12V DC at the same time.
Do not overload power supply
2. Operation
Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC
power supply, it should be connected to a power supply that allows for at
least 5w consumption.
(1) Mount a lens on the camera and connect equipment. Applicable lenses
are specified in Section 5 "LENS"
(2) Adjust the lens diaphragm and focus for optimum image.
5. LENS
6. AUTOMATIC ELECTRONIC SHUTTER (AES)
Exposure time is controlled automatically within a range of 1/60 sec. to
1/100000 sec. to obtain an adequate signal when the back panel switch is
turned to AES.
Back-Focus Adjusment
Back-Focus is adjusted at the factory to accommodate most standard lenses.
However, at times, slight adjustment to the IK-629A back-focus is necessary.
Focus Lock Screw
When the back panel switch is turned to VIDEO or DC, the exposure time is
fixed 1/60 sec.
Mount the Lens to the camera first. Then
loosen the Focus Lock Screw. Then rotate
the Focus ring until a clear image is achieved.
Afterwards, tighten the Focus Lock Screw.
Focus ring
7. BACKLIGHT COMPENSATION (BLC)
Nots
When the lens weight is more than 1 kg (2.2 lbs), support it on the lens side
rather than rely on screw that fix the camera to the tripod.
This function is activated when the BLC switch is set to on .
IRIS
O
N
ON
1
2
3
4
OFF
BLC
This camera supports two types of auto
-iris lens: Video-type and DC (direct drive)
Recorder Ready
types. Connect the auto-iris connector
When the automatic electronic iris and the auto iris lens is used, the exposure
adjustment is automatically performed so that a best picture is obtained at a
monitor zone of about 60% in horizontal and about 60% in vertical direction.
plug to the IRIS terminal on the side of
Auto iris lens
the camera. Refer to the chart below for
correct wiring and set up.
This function is effective when a strong light enters the portion other than
this zone and auto iris lens closes and darkens the area to view.
Video IRIS
Lens
Direct Drive
IRIS Lens
(Monitor screen)
3
1
4
2
_
1. + 12V
1. Damp (y)
IRIS
terminal
pin
2. NC
2. Damp+( )
3. VIDEO
4. GND
3. Driver+(wh)
60%
_
4. Driver (g)
IRIS
VIDEO
DC
Switch
position
position
60%
If the DAY / NIGHT LEVEL switch is set to Low (OFF position), the croma cut
level is set less than 20 to 30 IRE.
8. WHITE BALANCE (AWB)
O
N
ON
In this camera, the white balance is automatically adjusted corresponding to
the color temperature variations on the object.
1
2
3
4
OFF
DAY / NIGHT LEVEL
DAY / NIGHT (ON/OFF)
This camera is applicable to color temperature of 2500 to 10K.
If this switch is set to High (ON position), the croma cut level is set less than
40 to 50 IRE.
Note
O
N
ON
When external light and internal light are mixed or when the object includes
some chromatic colors are shot, a hue may partly have a little difference.
1
2
3
4
OFF
DAY / NIGHT LEVEL
DAY / NIGHT (ON/OFF)
The default setting is "Low". "High" is for a brighter setting than "Low".
9. LINE-LOCK PHASE
If two or more cameras within a system
have different AC line phases are switched
11. NOTES ON USE AND INSTALLATION
LEVEL
VIDEO OUT
DC 12V ...
H
L
by the video switcher, the picture on the
monitor TV will fluctuate vertically.
Connect 24V AC input lines of all cameras
so that they all share the same phase.
If you still have vertical fluctuation, adjust
the V.PHASE controller.
AES VIDEO DC
Do not aim the camera at the sun
Do not aim the camera at the sun or point it at sun even if you are not
shooting.
V
PHASE
AC 24V
~
GND
Do not shoot intense light
V. PHASE CONTROLLER
Intense light such as a spotlight may cause a bloom or smear. A vertical
stripe may appear on the screen. However , this is not a malfunction.
Treat the camera with care
Do not drop the camera or subject it to strong shock of vibration. Otherwise,
the camera may malfunction.
10. DAY / NIGHT FUNCTION
This function is activated when the DAY/NIGHT switch is set to on .
Under the low light condition, IK-629A automatically cuts the croma signal,
and displays the clear picture without noise.
Never touch internal parts
Do not touch the internal parts of the camera other than the parts specified.
Otherwise, the camera may malfunction.
Do not splash water on the camera
13. EXTERIOR VIEW
Install the camera where the camera can be kept dry. If the camera gets
wet, turn off the power and contact your dealer.
Install the camera
Where no video noise appears
If cables are wired near electric lighting wires or a TV set, noise may appear
in images. In this event, relocate cables or reinstall equipment.
Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than
specified. Otherwise, the quality of images may deterlorate or internal parts
may be affected. Special care is required to use the camera at high
temperature and humidity.
Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power
and contact your dealer. If you continue to use the camera when there
is something wrong with it , the trouble may much worse and an
unpredictable accident may occur.
12. IN CASE OF PROBLEMS
5 0
Condition
Check Points
Are the camera and connected equipment turned on?
Is the iris of the lens adjusted properly?
Are cables connected correctly?
No image
Is the monitor TV adjusted correctly?
Is the lighting too weak?
Unnatural color
SECTION 5
SPECIFICATIONS
1. SPECIFICAIONS
–
AC 24V ~ 10% 60Hz / DC 12V ... 10%
Power
Power consumption
IK-629A, IK-644A: 4.0w (max) with AI lens
IK-645A:
4.5w (max) with AI lens
Image sensor
1/3 inch CCD image area sensor
Image pickup area
4.96mm (0.195inch) horizontal x 6.0mm
(0.236inch) vertical (1/3inch type)
Effective picture element
IK-629A: 510 horizontal x 492 vertical
IK-644A, IK-645A: 768 horizontal x 494 vertical
Scanning system
Scanning frequency
Synchronization
Resolution
2 : 1 interlace NTSC Standard TV system
15.75kHz horizontal 60Hz vertical
Line-Lock, Internal manually switchable
IK-629A:
Horizontal 350 TV lines or more
Vertical 350 TV lines or more
IK-644A, IK-645A: Horizontal 480 TV lines or more
Vertical 350 TV lines or more
Minimum illuminance of subject
IK-629A: 0.2 Lux (F1.2, More than 10% of image output C = 0.45)
IK-644A: 0.3 Lux (F1.2, More than 10% of image output C = 0.45)
IK-645A: 0.2 Lux (F1.2, AGC WIDE, More than 10% of image output C = 0.45)
S/N
50 dB or more (AGC off, weight ON)
VBS 1.0V p-p / 75 ohms, composite
759 unbalanced
Video output
Output impedance
White balance
IK-629A, IK-644A: Automatic (2500.K to 10,000.K)
IK-645A:
Automatic (2500.K to 10,000.K), PRESET, MANUAL
Iris control
Video Out / Iris Driver Circuit Built in
Gain control
IK-629A, IK-644A: Average AGC, (24dB)
IK-645A:
Average AGC, On (24dB), Wide (30dB), OFF
Backlight compensation
IK-629A, IK-644A: Manual ON/OFF switching, center-bottom zone light measuring
system
IK-645A:
4 modes BLC function for different application
Lens mount
CS mount
Ambient temperature
Ambient humidity
Weight
–10°C to + 50°C (14°F to 122°F)
30% to 90%
IK-629A, IK-644A: 450g
IK-645A:
500g
External dimensions
2.74(W) x 1.97(H) x 4.56(D) inches (63x50x116mm)
ON (1/60s to 1/100000) / OFF (1/60s)
Automatic electronic shutter
|